![]() ![]() The T-bar should be located on the bottom side of the end band. Thread the wire through the top of the end band and down through the hole in the T-bar.Leaving approximately a one foot tail cut the wire.Pull the wire taut past the terminal post.When stretching short stretches, use a T-bar in lieu of a come-a-long and wire dog. Repeat this for the remaining two stretches.Do not over twist thus causing the wire to pop-out. Using your fence pliers, gently twist the wire at each barbwire arm to get the wire into the angled slot.Cut your barbwire and attach to the end band.When stretching the wire, there will remain a considerable amount of sag in the wire when stretched from terminal post to terminal post. A common mistake in stretching barbwire is stretching it too tight.Keeping constant pressure on the cable, crank the come-a-long until the barbwire is taut. ![]() Place the fixed end of the come-a-long into the eye of the wire dog.Wrap the cable end of your come-a-long the terminal post above the end band.Place your wire dog approximately ten feet from the terminal post. Pull the barbwire taut by hand along the fence line.At the other end of the stretch, pull the spool past the terminal post and estimate how much wire you will need to complete the stretch.It is important that you don’t leave loose loops around the wire because when tension is applied the wire may come unraveled. With tightly wound loops at least four times. With your pliers, bend a six inch section of barbwire around the nut and bolt located in the end band.Either way, slowly pull the barbwire along the inside of the fence line to the other terminal post.Or you may walk along the fence line allowing the barbwire to spool-out as you walk. You may use a stationary barbwire spooler to spin-out the barbwire as you pull the barbwire along the fence line. Locate the spool at the far end of the stretch.Evenly spaced and with the ears pointed down the fence line, tighten the bands. Install three end bands on each terminal post.If this is not clearly shown on your plans, specifications or proposal, obtain this information before preceeding with installing the arms. Having already installed the barbwire arms when stretching the fence, you will have already determined if the barbwire is to go in, out or vertical.Be sure that you are wearing safety glasses and gloves, keeping control of the materials at all times. Consequently, it has a tremendous capacity to cut and harm. Barbwire has either two point or four point barbs every 4” or 5” respectively. Again, it will want to unravel and tangle so firmly keep it in your grasp. Like tension wire, be careful when cutting loose the barbwire roll. When the wire is stretched it causes the twists to bind, thus creating a spring like action. The spring in barbwire comes from the twisting of two 12 ½ gauge wires around each other, completing five twist per foot. Unlike tension wire, barbwire is manufactured from mild steel materials. come-a-longs, pliers, bolt cutters, chop saw or hand saw, wire rake for the appropriate height wire, speed wrench with ½” socket, barb wire dog, T-bar, and hammer. Add chain-link mesh on the fence on the inside of the area so that the tension wire is between the poles and the mesh.Objective: By mastering this lesson, you will be able to barbwire installation.Įquipment: 2ea. Repeat for each stretch of fence between terminal poles around the fence line. ![]() Tighten the loops around the tight wire with pliers as on the other end. Tighten the brace brand completely with two sets of pliers as on the other end. Insert the loose end of the tension wire around the bolt and loop the additional wire around the tightened part of the tension wire. Attach a brace brand to the post 2 inches from the bottom by placing the bolt through both end holes and screw the nut on hand tight. Make the tension wire as tight as you can, using this method. You may use an electric winch in the same fashion.ĭepress and release the come-along handle to tighten the tension wire with each repetition. A come-a-long is a manually-operated winch. Attach the wire to a come-a-long and attach the come-a-long to the post with a sling made of rope or a towing strap. Walk 6 to 8 inches beyond the post and cut the wire at this point. Unroll the tension wire by walking along the fence line to the next corner or terminal post. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |